5V50MA 80Chs All-in-One Button Battery Test Equipment
Description
This equipment is used to test the adaptability of electrical, electronic and other products, components and materials in high and low temperature environments, as well as their performance during storage, transportation and usage. It is widely applied in aviation, automotive, scientific research and other fields, and serves as essential reliability testing equipment for new energy manufacturers and research institutes to test the performance of battery cells.
Product Performance
|
Testing Environment |
Operating Room Temperature: above 25℃ Relative humidity: ≤85%(No load) |
|
Testing Method |
GB/T 5170.2-2017 temperature test equipment |
|
Temperature Range |
-70℃～150℃ |
|
Fluctuation |
≤±0.5℃ (No load, or during stable temperature) |
|
Deviation |
±2.0℃ (No load, or during stable temperature) |
|
Heating Time |
+20℃→+150℃ ≤60 min (no load, average non-linearity) |
|
Cooling Time |
+20℃→-70℃ ≤75 min (no load, average non-linearity) |
Technical Parameter
|
5V50mA Battery Testing System |
|||
|
Items |
Values |
||
|
Resolution |
AD:24bit; DA:16bit |
||
|
Input impedance |
≥1G Ω |
||
|
Voltage |
CV output range |
10mV~5V |
|
|
Min discharge voltage |
-5V |
||
|
Accuracy |
± 0.02% FS |
||
|
Stability |
0. 04% of FS |
||
|
Current |
Output range/channel |
Range1: 0.1mA; Range2: 1mA; Range3: 10mA; Range4: 50mA |
|
|
Minimum output current |
0.2μA |
||
|
Accuracy |
± 0.02% FS |
||
|
CV cut-off current |
Range1: 0.1μA; Range2: 1μA; Range3: 10μA;Range4: 50μA |
||
|
Stability |
0.04% FS |
||
|
Power |
Output power/channel |
0.25 |
W |
|
Stability |
0. 08% of FS |
||
|
Time |
Current response time |
<1ms ( 10%FS~90%FS) |
|
|
Working step time |
≤ (365*24)h/step Time format-00:00:00.000(h, m, s, ms) |
||
|
Data record |
Data record conditions |
Min data record interval :100ms |
|
|
Min voltage change: 10mV |
|||
|
Frequency |
10Hz |
||
|
Charge |
Charge modes |
CC, CV, CCCV, CP |
|
|
Cut-off condition |
Voltage, Current, Time, Capacity, Energy, - ΔV |
||
|
Discharge |
Discharge modes |
CC, CV, CCCV, CP, CR |
|
|
Cut-off condition |
Voltage, Current, Time, Capacity, Energy |
||
|
Pulse |
Charge |
CC, CP |
|
|
Discharge |
CC, CP |
||
|
Min pulse width |
500ms |
||
|
Pulse counts |
Up to 32 |
||
|
Chg and Dschg switch |
Supported |
||
|
Cut-off condition |
Voltage, Time |
||
|
DCIR |
Calculated DCIR values available in BTSDA |
||
|
Cycle |
Max cycles |
65535 |
|
|
Max steps |
254 |
||
|
Cycle nest |
3 |
||
|
Protection |
Safety protection |
● Power-failure data protection |
|
|
● Offline operation mode |
|||
|
● User-defined protection conditions, such as upper and lower limited current/voltage, delay time, temperature, etc. |
|||
|
Dimensions |
|
|
Nominal Volume |
100L |
|
Inner Dimensions |
W500 mm×D500 mm×H500 mm |
|
Outer Dimensions |
W750 mm×D1220 mm×H1800 mm (Without bumps) |
|
Net weight |
About 280 kg |
Product Details
Hot Tags: all-in-one battery test system for button cell, China all-in-one battery test system for button cell manufacturers, suppliers, battery electronic component test device, battery microcontroller test gear, battery printed circuit board test apparatus